Several misunderstandings in the management of greenhouse tomatoes!

At present, the tomatoes in the northern greenhouse have gradually grown up, and some have already produced results. This is not the case. Lao Zhang went to the countryside again. When he visited the greenhouse, he discovered such problems and simply told everyone.

1. Fertilization has great blindness. The base fertilizer is too large, the nitrogen fertilizer is too much, and the biological microbial organic fertilizer is less. (Unfertilized chicken, duck manure and organic fertilizer, at best, it is a bit of nitrogen fertilizer, but also easy to produce ammonia gas, fertilizer, salt damage) The direct cause of tomato leaf hypertrophy and leaf hypertrophy is overgrowth. Tomato fruit is slow and does not open; soil organic matter content is low, mineral conversion rate is low, resulting in low fertilizer absorption rate; leaves are too large to cause transparency between branches and leaves. Poor sex, the lower part is prone to serious gray mold.

The leaves are hypertrophied.

2, the ridge is too low or even ridge. The consequence of this is that the ground temperature is low and the humidity is high. The root system of the tomato is in such an environment, and the root system is slow to develop, and even the root rot is caused, and the light is reduced, and the severe production is severe.

3. Improper use of anthers. Different concentrations of anthers should be used in different seasons and in different weather conditions. However, the people are saving things, and the weather is cloudy and sunny. The temperature is high and low, which can easily lead to a variety of deformed fruits, or adhesions, or grain exposure, which not only affects the value of the commodity, but also affects the yield.

4, the whole branch is not reasonable. Some leaves are poorly permeable, and some have excessive leafing, resulting in no leaves at the bottom. These are the two extremes: the leaves are poorly permeable, the nutrient-diverted fruit is insufficiently motivated, and the lower part is prone to gray mold; the lower leaf-leaved leaves have reduced photosynthesis ability, which also causes the fruit to slowly turn slowly.

5, root nodule root rot disease can not be divided into diseases and hospitalization. On the one hand, the medication is not correct, the input cost is increased, and the missed treatment time at the wrong time cannot recover the loss. For example, some farmers directly treat root-root worms as root rot treatments, can they be cured? Other farmers have directly burned the roots of tomatoes because of the concentration of the medicine.

Plants are wilting, mostly root problems. This picture shows the wilting of plants caused by root rot and blight.

Root rot specific performance.

Plant wilting caused by root knot nematodes

The performance of root knot nematodes.

6. Ignore the use of medium and trace element fertilizers. Most farmers only pay attention to the use of a large number of elements of NPK and neglect the use of trace elements such as boron, calcium, magnesium, zinc and iron, resulting in serious deficiency of tomatoes, or yellowing of leaves, or abnormalities of fruits. Affect the quality of the fruit.

7. The field management is extensive. The watering is suddenly large and small, and the temperature is not properly controlled by the wind. Some tomato plants are long, some are blasting, some are falling and falling.

In a word, the people have no technology and lack of technology! Many enterprise agrochemicals don't understand agricultural technology. When they go to shacks, they just sell medicines and sell fertilizers. It is understandable to sell products, but you must understand technology and don't know how to kill people!

This is also a lesson for our vast number of farmers. Crops are the most conscientious. If you take care of it scientifically, you will grow up with high yield and good quality. If you don’t know how to read it, you will be blind and you will grow it. Poor low yield and inferior revenge! Learning more science and using science will pay off!

Alloy steel refers to steel with high strength and good chemical stability at high temperature. It includes two types of anti oxidation steel (or high temperature resistant steel) and hot steel. Anti oxidation steel generally requires good chemical stability, but the capability is limited. High temperature strength and the corresponding oxidation resistance of heat and strong steel are required. Heat-Resistance Steel is often used in the manufacture of boiler, steam turbine, power machinery, industrial furnace and aviation, petrochemical and other industrial sectors in the work of the high temperature parts. In addition to the requirements of high temperature strength and high temperature oxidation corrosion, sufficient toughness, good shaping and welding are also required according to the different use, as well as a certain organizational stability. In addition,  some new low chromium nickel oxidation are also developed .Heat-Resistance Steel

Heat-Resistance Steel

Heat-Resistance Steel ,Heat-Resistant Material Handling Steel,Heat-Resistant Steel Tube,Heat-Resistant Black Round Steel Pipe

Jiangsu nickel alloy Co.,Ltd , https://www.xhalloy.com